Laparoscopic ultrasonic surgical scalpel full system
Introduction:
The Ultrasonic Generator System utilizes ultrasonic energy to
enable hemostatic cutting and/or coagulation of soft tissue. The
system consists of an ultrasonic generator, a foot switch, an
optional hand switching adaptor, a hand piece, and a variety of
open and minimally invasive instruments.
The Ultrasonic instruments vibrate longitudinally at 55.5
kilohertz. This ultrasonic vibration at the blade enhances its
cutting ability. The same vibration seals small vessels with
coagulated blood and tissue proteins.
The generator is a device (or generator) that is used to generate
and supply power and output control to an ultrasonic transducer.
Activating the footswitch or manual switch adapter provides power
output. The generator generates electrical energy signals that are
transmitted to the transducer through a cable and the transducer
converts the electrical energy signal into mechanical motion of the
ultrasonic wave.
Indications
The HARMONIC System is indicated for soft tissue incisions when
bleeding control and minimal thermal injury are desired. The
HARMONIC System instruments can be used as an adjunct to or
substitute for electrosurgery, lasers, and steel scalpels.
Contradiction
The instruments are not indicated for incising bone.
The instruments are not intended for contraceptive tubal occlusion.
System Components
Energy Generator
The generator supplies the hand piece with electrical energy and
facilitates selection of power levels, system
monitoring, and system diagnostics.
Power is delivered by activating the foot switch or hand switch.
Hand Piece
The hand piece contains an acoustic transducer that converts the
electrical energy supplied by the generator to mechanical motion.
The transducer is connected to an amplifier which amplifies the
motion produced by the transducer and relays it to the instrument.
Instrument
The mechanical motion from the hand piece advances to the
instrument, transmitting ultrasonic energy which enables hemostatic
cutting and/or coagulation of tissue.
| SN | Component name | Component models | Quantity | Remark |
|
Standard configuration | Generator | RXC-300 | 1pcs | |
| Foot switch | FS01 | 1pcs | Including cable lines |
| Hand Piece transducer | HP55.5S | 1pcs | |
| Hand Piece scalpel (Instrument) |
HP36P |
2pcs | Use under the view of endoscope |
| Instruction | / | 1pcs | |
| Warranty Card | / | 1pcs | |
| Certificate of conformity | / | 1pcs | |
| Packing List | / | 1pcs | |
|
Other Optional accessories | Instrument | HP23P | / | |
| Instrument | HP14P | / | |
| Instrument | HP9B | / | |
| Transducer | HP55.5B | / | |
| Note: In this manual, the term "instrument" refers specifically to
the scalpel of the RXC-300 ultrasonic scalpel system. |
Power Levels
The generator delivers two power levels: minimum (MIN) and maximum
(MAX). The minimum power level may be adjusted by the user from
Level 1 to 5. The maximum power level is always Level 5. With all
instruments except the ball coagulator, use a higher generator
power level for greater tissue cutting speed and a lower generator
power level for greater coagulation. For the ball coagulator,
higher generator power levels will provide greater coagulation. The
amount of energy delivered to the tissue and resultant tissue
effects are a function of many factors including the power level
selected, instrument characteristics, grip force (when applicable),
tissue tension, tissue type, pathology, and surgical technique.
FAQ
1. Q:Are you a factory or trading company?
A: We are a factory, we have rich experience for manufacturing Medical Device more than 10 years.
2.Q:Where is your factory located? How can i visit there?
A: Our factory is located in Jiaxing city, Zhejiang Province, China.
It is about more than 1 hours from Shanghai.
3. Q:Can you make samples?
A: Yes, we can make samples for you.
4. Q:How does your factory do as quality control?
A: Quality is the lift of our factory. We have inspector in
different post, and there are three inspectors before packing to
get best quality products.
5. Q: How is your post market service ?
A: If any damaged rings in the course of carriage, with the
checking it's our mistake, we will take full responsibility to compensate the customers.
6. Q:Can you do OEM for us?
A: Certainly. We also can build the moulding for our new customer.
7. Q:Does the price include freight?
A: No, please choose the express service provider or negotiate with
us.
